APEX 48-inch Lightweight Foam Four-Post Ramp Kit - Set of 2

Lightweight Foam Four-Post Lift Ramps for BendPak HD-9 and HD-7 Lifts

Factory four-post lift ramps get the job done, but they are often heavy, awkward, and steep enough to make loading lower vehicles more stressful than it needs to be. The APEX 48” Lightweight Foam 4 Post Ramp Kit replaces stock steel or aluminum ramps on compatible BendPak HD-9 and HD-7 series lifts with a lighter, easier-handling hook-nose ramp built for daily garage and shop use.Each ramp locks into the lift like the original drive-up ramps, but the experience is completely different. With a 48” length, 5” lift height, and smooth 5.7-degree approach angle, these lightweight four-post lift ramps help make vehicle loading faster, easier, and more controlled. One person can remove, carry, hang, and reinstall the ramps without turning every lift setup into a shoulder workout.

Designed Specifically for BendPak HD-9 and HD-7 Four-Post Lifts

The APEX 48” Foam 4 Post Ramp Kit is engineered for BendPak HD-9 and HD-7 series four-post lifts that use removable drive-up ramps. The hook-nose geometry, ramp profile, and pocket engagement are matched to the ramp receivers on these BendPak lift models for a secure, repeatable fit during vehicle loading and unloading.This kit is not intended or approved for use on other lift brands or lift models, even if the ramp pockets appear similar. Before installation, always confirm that your lift is part of the BendPak HD-9 or HD-7 family and that the correct ramp receivers are installed. When matched properly, APEX ramps provide a purpose-built upgrade for HD-9 and HD-7 owners who want easier handling, cleaner loading, and a better everyday lift experience.

Low 5.7-Degree Approach Angle for Faster, Cleaner Loading

Not every shop or garage needs a long 96” ramp. The 48” APEX ramp kit is built for users who want a compact footprint, faster loading, and a friendlier approach angle than many factory steel ramps. At 48” long with 5” of lift, these ramps hit a practical sweet spot for standard ride height vehicles, performance cars, and many mildly lowered vehicles that see regular lift use.The 5.7-degree approach angle helps reduce drama with front lips, splitters, long overhangs, and low-clearance bodywork. For general service, oil changes, inspections, detailing, storage, and everyday four-post lift use, these lightweight foam ramps make it easier to load vehicles smoothly without dragging out extra boards, blocks, or questionable garage science.

Reinforced EPS Foam Core with Durable Polyurea Grip

APEX ramps are built around a proprietary high-density expanded polystyrene structural foam core that is solid, lightweight, and designed to support serious vehicle weight without the bulk of steel. Unlike hollow plastic ramps, the dense EPS core does not collapse, echo, or feel unstable under the tire. It also resists rust, water absorption, oil absorption, and heat transfer while providing natural damping under load.Each ramp is fully encapsulated in a high-performance polyurea elastomer coating that bonds to the foam core and creates a tough, flexible outer shell. The micro-textured surface helps provide grip under the tire and at the floor interface, helping the ramp stay put during drive-on maneuvers on smooth concrete or epoxy-coated floors. Inside the hook nose, a precision-formed internal reinforcement with an S-shaped contour runs deep into the foam core, creating a mechanically anchored connection that acts like part of the ramp instead of a plate glued to the front.

Built for HD-9 and HD-7 Lifts

Designed specifically for BendPak HD-9 and HD-7 series four-post lifts with removable drive-up ramps. The hook-nose profile matches compatible ramp receivers for a secure, repeatable fit.

Lightweight Foam Construction

The high-density EPS structural core keeps each ramp strong without the back-breaking weight of steel. One person can remove, carry, hang, and reinstall the ramps with ease.

Low 5.7-Degree Approach Angle

A smoother 5.7-degree approach helps make loading performance cars, mildly lowered vehicles, and long-overhang vehicles easier. Less scraping, less guessing, less garage gymnastics.

Reinforced Hook-Nose Design

An internal S-contour reinforcement runs deep into the foam core and is mechanically anchored before coating. The hook acts like part of the ramp, not an afterthought glued to the end.

Polyurea Grip Coating

The ramp is encapsulated in a tough, flexible polyurea coating built to resist abrasion, impact, and common shop fluids. A micro-textured surface helps improve tire and floor grip during loading.

Compact 48-Inch Ramp Length

The 48” length is ideal for users who want faster loading and easier storage without jumping to oversized ramp setups. It is a practical upgrade for service work, detailing, inspections, and daily lift use.